Hollow section expansion bolt - Structural engineering general discussion (2024)

Eng-Tips is the largest engineering community on the Internet

Intelligent Work Forums for Engineering Professionals

RegisterLog in

  • Home
  • Forums
  • People
  • Structural Engineers
  • Structural engineering general discussion
  • Thread starterRamezsayed EIT
  • Start dateJul 13, 2020
Status
Not open for further replies.
  • Jul 13, 2020
  • #1

Ramezsayed EIT

Structural
Jan 9, 2020
20
0
0
US

Hey

I am designing a connection of cantilever beam with end plate connected to HSS Beam. The customer doesn't want to weld the end plate to the beam so I proposed the HSS expansion bolts

Hollow section expansion bolt - Structural engineering general discussion (2)

it seems that these bolts are very expensive so they came back to me asking for different type of connection. Is there any other option that I don't know ?

Ultimate tensile load / bolt = 4400 lbs
Ultimate Shear / bolt = 390 lbs

Replies continue below

Recommended for you

Sort by dateSort by votes

  • Jul 13, 2020
  • #2

Tmoose

Mechanical
Apr 12, 2003
5,626
0
0
US

How far is the cantilever beam from the end of the HSS "beam" ( column ?).
I'm thinking maybe a "nut plate" could be fed down into HSS "beam" ( column ).
Could a nice thick plate be welded to the outside of the HSS "beam" ( column ?) and holes drilled and tapped for standard fasteners?

Upvote0Downvote

  • Jul 13, 2020
  • #3

dauwerda

Structural
Sep 2, 2015
1,027
0
36
US

I have seen through-bolts used with sleeves installed on the HSS, although I imagine that would cost just as much if not more than the Hollo-Bolts. You could have a beam stub welded directly to the HSS, moving the bolted end plate connection away from the face of the HSS. Flow drilling is another option with HSS - I'm not sure how the cost of that compares to a Hollo-Bolt.

Upvote0Downvote

  • Jul 13, 2020
  • #4

JLNJ

Structural
Oct 26, 2006
1,986
0
0
US

Small cantilever? Shop weld.

Tell us the geometry and we can provide better suggestions.

Upvote0Downvote

  • Jul 13, 2020
  • Thread starter
  • #5

The cantilever is 60" projected (cantilevered canopy outriggers)
spacing = 48"
cantilever HSS 3" x 1/2" x 1/4"
End plate fillet welded at the end of HSS 8" x 6" x 3/4"
Main HSS Beam is 12" x 6" x 3/8”

Main beam is existing and the outriggers will be fabricated in the warehouse.

Upvote0Downvote

  • Jul 13, 2020
  • #6

GC_Hopi

Structural
Jun 24, 2018
546
0
16
US

Shop weld a beam stub or plate to the HSS that will give you something to bolt to.

Upvote0Downvote

  • Jul 13, 2020
    1
  • #7

Agent666

Structural
Jul 2, 2008
3,080
0
0
NZ

One thing to keep in mind as well regarding the lindapter type hollo bolts if you go down that route is that the actual external diameter/size is quite a bit larger than the nominal diameter/size due to the sleeved design.

It can take out quite a bit of your column section if you get into the larger sizes which potentially needs some assessment.

The other thing is that they require a hole tolerance much tighter than the typical 2mm oversized hole for a typical structural bolt. Something like 1/2 a millimeter from memory (go look at the suppliers documentation though to confirm).

Propose no canopy, that's the cheapest option for those types of clients who take offense at pretty much everything logical.

Upvote0Downvote

  • Jul 13, 2020
  • #8

Eric C.

Civil/Environmental
Feb 24, 2020
57
0
6
US

Why is your customer objecting to welding the plate to the beam? It would seem that most other options are either more costly or more time consuming (way more costly).

Upvote0Downvote

  • Jul 13, 2020
  • #9

MIStructE_IRE

Structural
Sep 23, 2018
816
0
0
IE

Weld will look waay better here! And will likely be a better job anyway.

Upvote0Downvote

  • Jul 13, 2020
  • #10

Retrograde

Structural
Aug 26, 2015
586
0
16
AU

dauwerda said:

I have seen through-bolts used with sleeves installed on the HSS, although I imagine that would cost just as much if not more than the Hollo-Bolts.

In my experience the through bolts with sleeves are significantly cheaper than hollo-bolts. That's the option I would choose.

Upvote0Downvote

  • Jul 14, 2020
  • #11

Tomfh

Structural
Feb 27, 2005
3,363
0
36
AU

Retrograde said:

In my experience the through bolts with sleeves are significantly cheaper than hollo-bolts

Good strong detail too.

Upvote0Downvote

  • Jul 14, 2020
  • #12

dhengr

Structural
Sep 22, 2009
4,669
0
36
US

Ramezsayed EIT:
I’m so damn sick and tired of clients asking for stupid, impossible things/details and then insisting that they be cheap, simple and invisible too. But, not your first way, or your second and third ways, etc. etc. Tell them you don’t need those damn canti’s. for your part of the structure, so just note “see Arch.” on your plans, and be done with it. Let them figure it out. They could save a whole bunch of their money by eliminating all the canti’s. Shop weld a very thick pl. to the side of the main beam. Tap this side pl. for the canti. moment end bolts which you need for the end pls. on the canti’s. The side pl. has to be thick enough and of strong enough yield strength so that the tapped depth is enough so the bolt won’t bottom out, and still has sufficient engagement for the bolt loads needed. Don’t forget to check the main beam for the torsion that these canti’s. introduce. If it is only a 60” canti., the main beam can be shop fabed. with the canti’s. welded to the side of the beam. This is a truck deliverable sub-assembly in 30 or 40’ lengths.

Upvote0Downvote

  • Jul 14, 2020
  • Thread starter
  • #13

Ramezsayed EIT

Structural
Jan 9, 2020
20
0
0
US

dhengr

They are super exhausting!

Designed a welded connection and the came back telling me that they don't have welders on site and they are not willing to hire one
Designed a bolted connection and they told me its expensive option

I actually suggested using stud bolts(nelson stud welding) or bolt with sleeve. Main beam will be designed by others but I provided all of the reactions on it so they can check the design as you mentioned.

Thanks all for your cooperation.

Upvote0Downvote

  • Jul 14, 2020
  • #14

Settingsun

Structural
Aug 25, 2013
1,513
0
0
AU

Is the sleeve loose or welded to the hollow section?

Upvote0Downvote

  • Jul 15, 2020
  • #15

Ron

Structural
Sep 24, 1999
16,336
0
36
US

I agree with dhengr...sometimes clients are just a pain in the a$$ and have to be told how it needs to be. They want our advice but tend to convince themselves that they know more than we know. Then there's the impossible ones that want everything for nothing....remember, you have three options to give them...fast, cheap and good....they can only have two out of the three.

Upvote0Downvote

  • Jul 15, 2020
  • #16

Agent666

Structural
Jul 2, 2008
3,080
0
0
NZ

With most contractors it's one out of three?....

Upvote0Downvote

Status
Not open for further replies.

Similar threads

  • Locked
  • Question

Circular Hollow Section - Maximum Thickness

  • EngrRC
  • Jun 25, 2024
  • Structural engineering general discussion
Replies
3
Views
12

Jun 25, 2024

JStephen

  • Locked
  • Question

Rebar cages for concrete filled hollow section (CFHS) columns

  • user277418
  • May 17, 2024
  • Structural engineering general discussion
Replies
6
Views
13

Jun 2, 2024

user277418

  • Locked
  • Question

Hollow Core Plank Stirrups?

  • grogannc
  • Jul 29, 2024
  • Structural engineering general discussion
Replies
14
Views
15

Jul 30, 2024

Ingenuity

  • Locked
  • Question

Roof Expansion Joints

  • pioneer09
  • Aug 27, 2024
  • Structural engineering general discussion
Replies
0
Views
12

Aug 27, 2024

pioneer09

  • Locked
  • Question

Bolt clearance2

  • JStructsteel
  • Sep 5, 2024
  • Structural engineering general discussion
Replies
11
Views
18

Sep 6, 2024

JStructsteel

  • Home
  • Forums
  • People
  • Structural Engineers
  • Structural engineering general discussion
Hollow section expansion bolt - Structural engineering general discussion (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Lakeisha Bayer VM

Last Updated:

Views: 6203

Rating: 4.9 / 5 (49 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Lakeisha Bayer VM

Birthday: 1997-10-17

Address: Suite 835 34136 Adrian Mountains, Floydton, UT 81036

Phone: +3571527672278

Job: Manufacturing Agent

Hobby: Skimboarding, Photography, Roller skating, Knife making, Paintball, Embroidery, Gunsmithing

Introduction: My name is Lakeisha Bayer VM, I am a brainy, kind, enchanting, healthy, lovely, clean, witty person who loves writing and wants to share my knowledge and understanding with you.